Bestwinterproducts.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

How to Flush a Rinnai Tankless Water Heater with Vinegar

Prime for Young Adults: check your eligibility on Amazon

Check beneath the heater to confirm it has two dedicated service valves with threaded hose caps. These shutoff ports allow you to pump plain white vinegar through the internal heating pipes for forty-five minutes to dissolve rock-hard mineral scale. Clearing out that buildup restores steady heat and prevents the system from throwing sudden error codes.

Doing the job safely hinges on three simple details. Electric power and gas lines must stay completely off so the burner never fires while dry. The setup also requires isolation valves (shutoff handles fitted with hose spigots) and standard grocery-store vinegar instead of harsh chemical cleaners. The steps below walk through the entire hookup to get your hot water running smoothly again.

What supplies do you need before starting?

Flushing your tankless water heater does not require complicated plumbing tools, but you do need a few specific items on hand before you close any valves. Gathering everything ahead of time keeps the process smooth and prevents messy spills on your utility room floor.

  • A 5-gallon bucket: A clean plastic bucket serves as your vinegar reservoir and catches the circulating fluid as it leaves the heater.
  • A small submersible utility pump: You need a compact water pump (typically 1/6 horsepower) with standard garden hose male threads on the outlet. The pump must sit completely flat on the bottom of your bucket.
  • Two short garden hoses: Standard six-foot rubber garden hoses or washing machine hoses work best. Ensure both hoses have good rubber washers inside the female couplings to prevent spraying leaks.
  • Three to four gallons of white vinegar: Use plain, undiluted food-grade white distilled vinegar with 5 percent acidity from the grocery store. Never use industrial chemicals, harsh chemical descalers, or muriatic acid, as these eat away at the copper internal water heating pipes (heat exchanger) and void the manufacturer warranty.
  • An adjustable wrench or channel-lock pliers: You need these to unscrew the service port caps and loosen the cold water inlet filter plug.
  • Old rags or a towel: A few towels placed directly under the plumbing connections will catch small drips when you open the purge caps.

How do you safely shut down the heater?

Safety comes first when working on any appliance connected to gas, high voltage, and pressurized water. You must cut both power and fuel before touching the water lines so the burner does not fire during the flush.

  1. Cut the electrical power: Unplug the unit power cord from the wall outlet. If your unit is hardwired directly into a junction box, switch off the dedicated circuit breaker in your main electrical panel. The digital display on the front of the heater should go completely blank. If power remains active, the computer board might sense fluid moving during descaling (clearing out hardened mineral scale) and attempt to ignite the burner without full water pressure, which can destroy internal parts.
  2. Shut off the gas supply: Trace the gas pipe running into the bottom of the heater. Look for a manual shutoff valve, which usually features a yellow or red handle. Turn this handle a quarter turn until it sits perpendicular (at a right angle) to the pipe. This blocks fuel from reaching the burners.
  3. Close the main household water lines: Look directly beneath the heater for the service isolation valves (shutoff valves with hose ports). You will see a cold water pipe (usually marked with a blue handle) and a hot water pipe (usually marked with a red handle). Turn both of these large handles ninety degrees so they point across the pipes. This completely isolates the heater from your home, guaranteeing that no vinegar gets pushed into your drinking taps or showers.

In tight utility spaces, such as manufactured housing where plumbing sits in compact alcoves similar to clearances around a heater for mobile home installation, double-check that you have clear access to turn both handles fully into the locked, closed position.

How do you connect the hoses and pump?

Once the heater is isolated from the rest of your home, you can connect your pump and hoses to create a closed loop. Take your time threading each connection straight so you do not damage the brass threads on the service ports.

  1. Remove the service port caps: Directly on the sides of the blue and red isolation valves, you will find small brass caps. Unscrew both caps counterclockwise with your fingers or an adjustable wrench. Keep a rag underneath, as a small amount of trapped water will dribble out. Check inside both caps to make sure the small black rubber washers do not fall out onto the floor.
  2. Attach the pump supply hose: Screw one end of your first hose onto the threaded outlet of your submersible pump. Screw the opposite end of that hose onto the cold water service port (the spigot attached to the blue valve). Hand-tighten the connection firmly, then give it a gentle quarter turn with pliers to seat the rubber washer.
  3. Attach the hot return hose: Screw one end of your second hose onto the hot water service port (the spigot attached to the red valve). Place the loose end of this hose down into the bottom of your 5-gallon bucket.
  4. Add the vinegar: Place the submersible pump flat on the bottom of the bucket. Pour three to four gallons of plain white vinegar directly into the bucket until the pump body is completely submerged. Keeping the pump fully underwater prevents it from sucking air and overheating.
  5. Open the small service valves: On the brass service ports where you just connected your hoses, find the small brass T-handles. Turn both of these small handles so they sit parallel to the hose spigots. This opens the internal passage into the heater while leaving the main lines to your house closed.

How long should you circulate the vinegar?

Plug the submersible pump into an electrical outlet to start circulating the fluid. Vinegar will immediately flow out of the bucket, travel into the cold service port, push through the internal water heating pipes, and pour out of the hot return hose back into your bucket.

Let the pump circulate the vinegar continuously for 45 to 60 minutes. If you live in an area with hard municipal water, or if you have not flushed your unit in over two years, let the pump run for a full 75 to 90 minutes. The mild acetic acid in the vinegar needs time to slowly dissolve chalky calcium and magnesium buildup clinging to the copper walls.

Keep a close eye on the bucket during the first fifteen minutes of circulation:

  • The vinegar will gradually change from clear to cloudy, and you may see small white or tan flecks of calcium drifting in the liquid.
  • A light foam or fizzing at the surface is completely normal. This foam indicates that the acid is actively reacting with mineral buildup inside the copper core.
  • The fluid might take on a faint blue or green hue toward the end of the hour. This slight color shift happens when vinegar reacts with harmless surface copper oxides on the pipe interior.

If you perform this maintenance during cold winter months in an unheated space like an attached garage, cold temperatures can slow down the cleaning speed of the vinegar. Keeping the space tempered with a dependable heater for garage with thermostat regulation helps the liquid stay warm enough to dissolve scale efficiently. Never let the pump run completely dry; if the fluid level drops below the pump intake, unplug the unit immediately and top off the bucket with another half gallon of vinegar.

How do you rinse the heater and clean the screen?

After the circulation time finishes, you must flush out every drop of vinegar and remove any loosened grit from the internal water passages before restoring regular household service.

  1. Drain and discard the used vinegar: Unplug the submersible pump and lift the return hose out of the bucket. Pour the dirty vinegar down a household drain or toilet, and rinse the bucket out with fresh tap water.
  2. Flush the heater with clean water: Keep the hot return hose connected to the red service port with its open end pointed into the empty bucket (or directed toward a floor drain). Close the small brass T-handle on the cold service port and unscrew the pump hose. Now, slowly open the main cold water supply handle (the large blue valve). Fresh household water will rush through the heater, push remaining vinegar out of the internal lines, and pour out through the hot return hose. Let fresh water run through for three to five full minutes until the discharge smells completely clean with no sour vinegar scent remaining.
  3. Close the hot service port: Turn the small T-handle on the hot service port ninety degrees to shut it off. Unscrew your return hose, wipe the port threads dry, and reinstall the brass protective caps onto both service ports. Snug the caps down gently with an adjustable wrench.
  4. Clean the cold inlet filter screen: Directly beside or beneath the cold water connection sits the in-line filter (a small mesh screen inside the cold inlet). Turn the main blue cold water valve back to the closed position to avoid pressure spray. Place a rag underneath, unscrew the plastic or brass filter plug counterclockwise using pliers, and pull the cylindrical mesh screen out. Rinse away trapped sand, sediment, and loosened scale under a sink faucet. Slide the clean screen back into place, thread the plug in by hand to prevent cross-threading, and tighten it gently with your tool.

How do you turn everything back on?

Restoring your water heater to normal operation requires opening the plumbing lines in a specific order so you can purge trapped air pockets before firing the gas burner.

First, open both the main cold water inlet valve (blue handle) and the main hot water outlet valve (red handle) completely so the handles run parallel with the copper pipes. At this point, water pressure is restored to the heater, but the lines still contain trapped air from the flush.

Walk to the nearest bathroom or kitchen sink and open the hot water tap completely. The faucet will spit, sputter, and hiss loudly as trapped air rushes out of the plumbing. Let the water run until it settles into a smooth, quiet stream, then turn the faucet off. Walk back to your Rinnai unit and inspect the service caps and the filter plug for any moisture or slow drips.

Next, reopen the yellow gas shutoff valve by turning the handle parallel to the gas line. Plug the power cord back into the electrical outlet or flip the circuit breaker back on. The digital controller will chime and light up with your standard set temperature.

Finally, turn the hot water tap on at your sink once more. Within a few seconds, you should hear the Rinnai internal combustion fan start up, followed by the soft click and steady rumble of the gas burner igniting. Check that the water running from the faucet turns comfortably hot within its normal delivery time.

FAQs

Can you use cleaning vinegar or muriatic acid instead of food-grade vinegar?

Use standard food-grade white distilled vinegar with 5 percent acidity rather than concentrated cleaning vinegar or harsh acids. Commercial cleaning vinegars often reach 10 to 30 percent acidity, while muriatic acid is significantly more corrosive. Strong acids can quickly pit the thin copper walls inside the heat exchanger, degrade rubber internal O-rings, and cause permanent leaks. Food-grade vinegar provides the ideal balance of mineral-dissolving power without risking damage to internal metal surfaces.

How often does a Rinnai tankless water heater need flushing?

Most homes require a thorough flush once every twelve months to maintain optimal water heating efficiency and flow rates. If your home uses hard well water or municipal water with high mineral counts above 7 to 10 grains per gallon, you may need to flush the heater every six to nine months. Homes equipped with an effective whole-house water softener can often stretch maintenance to every eighteen to twenty-four months.

What should you do if your Rinnai heater does not have isolation valves?

If your heater was installed with solid copper pipes soldered directly to the inlet and outlet without service ports, you cannot perform a vinegar flush yourself. You must contact a licensed plumber to install a proper tankless isolation valve kit beneath the unit. These valve kits feature built-in quarter-turn shutoffs and threaded purge ports specifically engineered to make regular home descaling safe and manageable.

Will flushing clear a Rinnai error code like LC or 20?

Yes, flushing often clears an LC code (which indicates lime and scale buildup) or error code 20 (which indicates a combustion or heat transfer issue caused by scale insulation). Once you complete the full descaling cycle and rinse the system thoroughly, unplug the electrical cord for thirty seconds to reset the computer board. If the error code reappears immediately after restoring power, call a certified technician to inspect the internal sensors and gas burner calibration.

4.3
3 ratings
James Tindall
WRITTEN BY
James Tindall
James here! I’m a New Yorker who’s been exploring the world of winter and outdoor products for over 10 years. If it can be worn or used in the great outdoors, I've probably reviewed it.