How to Flush an AO Smith Tankless Water Heater with Vinegar
Most homeowners assume cleaning a tankless water heater demands harsh chemical cleaners or an expensive service call. In reality, you only need to circulate plain white vinegar through the unit with a small utility pump for forty-five to sixty minutes. This gentle soak dissolves the hard, chalky mineral scale that bakes onto the internal heating coils, protecting your hot water flow and preventing sudden temperature drops.
A few specific factors change the exact routine. Your local water hardness determines how often this is necessary, since mineral-heavy well water requires more frequent descaling than treated city water. You will also need to confirm that service isolation valves (the colored shut-off levers right under the cabinet) are installed, and check whether you are cutting power to an electric model or shutting off a gas line. The steps below walk through the entire setup so you can tackle it with confidence.
Gather a Bucket, Pump, Hoses, and Four Gallons of Vinegar
Hard water minerals like calcium and magnesium naturally collect inside your water heater over time. Every time the burner fires up, those minerals bake onto the metal heating coils inside the unit. Over several months, this hard chalky mineral buildup forms a crust that acts like an unwanted insulating blanket. The unit struggles to transfer heat into the water, which leads to lukewarm showers, higher energy bills, and system error codes. Flushing your water heater once a year dissolves that crust and protects the internal components from overheating.
Before you begin, gather the following supplies:
- Four gallons of plain white household vinegar: Standard, undiluted white vinegar from the grocery store is ideal.
- A five-gallon plastic bucket: Make sure the bucket is clean and free of dirt, laundry soap, or debris.
- A submersible pump: This is a small water pump placed inside a bucket to push cleaning liquid through the plumbing lines. A standard utility pump rated at one-sixth or one-fifth horsepower works best.
- Two short hoses: Standard garden hoses or washing machine supply hoses measuring five to six feet in length, fitted with standard female hose connections on both ends.
- An adjustable wrench or channel-lock pliers: Useful for loosening tight service caps and snugging hose fittings.
- A pair of old towels or rags: Kept on the floor to catch small drips while you connect and disconnect lines.
Many homeowners wonder if they can use regular household white vinegar instead of chemical descaling solutions. Plain white vinegar is actually the safest choice for an A.O. Smith unit. It contains about five percent acetic acid, which is strong enough to dissolve calcium scale over an hour, yet mild enough that it will not eat through copper pipes, brass fittings, or rubber seals. Harsh chemical descalers and muriatic acids can strip the protective metal lining inside the heating coils, cause pinhole leaks, and void your manufacturer warranty.
You also need to check underneath your heater to make sure service isolation valves are installed. These are shut-off levers that block house water while opening small threaded side ports for cleaning. Most modern tankless installations have these valve kits directly below the unit, color-coded with blue and red handles. If your water heater is connected directly to solid home pipes without these special T-shaped valves, you cannot flush the unit yourself yet. A licensed plumber must install an isolation valve kit before you can proceed.
Shut Off the Gas, Power, and Main Water Valves First
Safety comes first whenever you service any water heating appliance. You must completely cut off the power, fuel, and incoming household water before touching any plumbing connections. If the unit attempts to fire up while you are circulating vinegar or while the water lines are empty, the internal heating coils can warp and scorch within seconds.
- Disconnect the electrical power: Unplug the water heater power cord from the wall electrical outlet. If your unit is hardwired directly into a junction box without a standard wall plug, walk to your main electrical panel and switch the dedicated circuit breaker to the "Off" position. Look at the digital control screen on the front of the heater to confirm the display is completely blank.
- Turn off the fuel supply: If you have a natural gas or propane model, locate the yellow shut-off handle on the gas line running into the bottom of the heater. Turn this handle one-quarter turn so that it sits perpendicular (across) the gas pipe. When the handle forms a cross with the pipe, the gas flow is completely shut off. If you have an all-electric tankless unit, shut off the double-pole breakers that feed the heating elements.
- Close the cold water supply valve: Look at the water pipes directly under the heater. Find the cold water isolation valve, which features a blue handle on the right-hand pipe. Turn this blue handle 90 degrees so that it sits perpendicular to the water pipe. This blocks cold household water from entering the unit.
- Close the hot water outlet valve: Find the hot water isolation valve, which features a red handle on the left-hand pipe. Turn this red handle 90 degrees so that it also sits perpendicular to the pipe. This blocks water inside the heater from escaping into the hot water faucets throughout your home.
Knowing which valves to turn off first comes down to a simple rule: always shut down your heat source before you touch the water levers. Turning off the electricity and fuel prevents the burners from igniting unexpectedly. Once the unit is dead silent and dark, closing the main blue and red isolation levers ensures that vinegar stays trapped strictly inside the water heater during the cleaning process.
Connect the Pump and Hoses to the Service Ports
With the water heater fully isolated from your home plumbing, you can now attach your pump and hoses to the service ports. These ports are small brass outlets with threaded male hose connections located on the sides of your blue and red valve bodies.
- Place your towels and bucket: Spread an old towel on the floor directly beneath the water heater. Set your clean five-gallon bucket on the towel, positioned right below the plumbing lines.
- Remove the service port caps: Unscrew the brass caps from both the blue cold service port and the red hot service port by turning them counterclockwise with your fingers or an adjustable wrench. Set the brass caps aside in a safe spot. A few drops of trapped water may trickle out into your bucket, which is completely normal. Check that the small black rubber washers remain seated inside the caps so they do not get lost.
- Connect the pump supply hose: Take your first hose and thread one end onto the discharge outlet of your submersible pump. Thread the opposite end of that same hose onto the cold water service port (the port next to the blue handle). Hand-tighten the fitting firmly, then use your pliers to give it a gentle quarter-turn.
- Connect the return drain hose: Take your second hose and thread one end onto the hot water service port (the port next to the red handle). Tighten it firmly by hand. Place the loose, open end of this second hose directly down into the bottom of the five-gallon bucket.
- Fill the bucket with vinegar: Pour all four gallons of plain white vinegar into the bucket. Place the submersible pump flat on the bottom of the bucket. Make sure the pump body is fully covered by the liquid so it does not suck in air when started.
If you notice water leaking from the service caps or hose connections during setup, do not panic. Small drips usually mean a rubber garden hose washer is missing, twisted, or worn out. Unscrew the fitting, confirm that a clean rubber washer sits flat inside the female connection, and screw it back on hand-tight. Avoid cranking down on brass fittings with heavy tools, as excessive force can crack the brass threads or crush the internal rubber seal.
Run the Vinegar for an Hour and Clean the Filter
Now that your closed circulation loop is assembled, you can start pumping vinegar through the metal heating coils inside the unit. The pump pushes vinegar into the cold water inlet, forces it up through the internal passages where it eats away mineral deposits, and expels it out the hot water side back into your bucket.
- Open both service port valves: Locate the small T-shaped handles on the sides of the service ports where your hoses are connected. Turn both small handles 90 degrees so they line up parallel with the service outlets. Keep the main blue and red isolation levers closed (perpendicular to the pipes).
- Start the circulation pump: Plug the submersible pump power cord into a nearby 120-volt electrical wall outlet. The pump will hum to life and immediately begin drawing vinegar from the bucket. Within a few seconds, liquid will begin pouring out of the return hose back into the bucket, creating a continuous loop.
- Inspect the setup for leaks: Watch all hose connections closely for the first two minutes of operation. If you see a fine spray or steady drip, unplug the pump immediately, snug the leaking hose fitting with your pliers, and plug the pump back in.
- Let the pump run for 45 to 60 minutes: Allow the vinegar to circulate without interruption. If you live in an area with moderately hard water, 45 minutes is usually enough. If you have severe hard water, have noticed white crust around your aerators, or have gone more than a year without descaling, let the pump run for a full 60 minutes.
As the pump runs, watch the liquid in the bucket. The clear vinegar will gradually turn cloudy or take on a pale blue-green tint. This color change happens when the mild acetic acid reacts with copper tubing and dissolves baked-on minerals. You will likely see small white flakes of calcium scale settle onto the bottom of the bucket.
While the pump is circulating, take time to clean the cold water inlet sediment filter. This is a small removable screen that catches grit, sand, and pipe rust before water enters the unit:
- Find the small round plug located near the cold water inlet at the bottom base of the heater.
- Place a towel directly under the plug to catch water.
- Turn the plug counterclockwise by hand or with pliers to unscrew it from the heater body.
- Pull the cylindrical mesh screen out from the housing.
- Rinse the screen under a clean sink faucet, brushing away trapped grit with an old toothbrush until the tiny holes are clear.
- Slide the clean filter back into its slot and screw the plug clockwise until it is snug. Do not overtighten the plastic threads.
Flush with Fresh Water Before Turning the System Back On
Once the circulation time is complete, you must flush the system with fresh household water. Rinsing cleans out every trace of sour vinegar and carries away any loose mineral flakes still lingering inside the pipes. Skipping this step can leave an unpleasant smell in your home water lines and may push grit into your sink aerators.
- Shut off the pump: Unplug the submersible pump from the electrical wall outlet. Lift the pump out of the bucket and set it on your towel.
- Dispose of the used vinegar: Carry the five-gallon bucket to a nearby utility sink, floor drain, or toilet and dump out the dirty vinegar and mineral sediment. Rinse the bucket clean and place it back under the heater.
- Disconnect the cold supply hose: Close the cold water service port valve by turning its small T-handle perpendicular to the hose port. Unscrew the pump hose from the cold service port.
- Prepare the hot water drain line: Leave the hot return hose connected to the hot service port with the small T-handle open. Make sure the loose end of this hose points securely down into your empty five-gallon bucket or runs directly into a nearby floor drain.
- Blast the unit with fresh water: Slowly turn the main cold water isolation valve (the blue lever) so it sits parallel to the pipe. Cold household water under full street pressure will surge through the water heater, scour the heating coils, and spray out through the hot service hose into the bucket.
- Rinse for three to five minutes: Let fresh water blast through the heater continuously. If you are draining into a bucket, keep a close eye on the water level. When the bucket is three-quarters full, close the main blue valve, dump the bucket down your drain, and reopen the blue valve. Continue rinsing until the discharge water runs crystal clear and has no lingering vinegar odor.
- Seal the service ports: Close the hot water service port valve by turning its small T-handle perpendicular. Unscrew the drain hose from the port. Reinstall the brass service caps onto both the cold and hot service ports, tightening them firmly with your wrench to prevent drips.
- Reopen the main plumbing lines: Turn both the main cold water isolation valve (blue handle) and main hot water isolation valve (red handle) parallel to the pipes. Water is now free to flow normally through the heater and into your home.
- Purge air from the house pipes: Walk to the nearest bathroom or kitchen sink and open the hot water tap completely. The faucet will cough, hiss, and sputter as trapped air escapes from the plumbing lines. Let the water run until it flows in a smooth, steady stream without spitting, then turn the faucet off.
- Restore power and fuel: Turn the yellow gas valve handle parallel to the pipe so gas flows freely. Plug the electrical power cord back into the wall outlet or flip the breaker on. The digital display on your A.O. Smith heater will illuminate. Run a hot water faucet once more to verify that the internal fan starts, the burner ignites, and hot water flows reliably.
Call a Plumber if You Spot Leaks or Error Codes
Flushing an A.O. Smith tankless water heater is straightforward routine maintenance, but certain situations call for professional plumbing help. Knowing when to put your tools away protects your home from costly water damage and prevents safety hazards.
Call a licensed professional if you encounter any of the following issues:
- Persistent diagnostic error codes: A.O. Smith units display specific numerical error codes on their digital control screens when something goes wrong. If an error code for ignition failure, abnormal combustion, or temperature sensor faults reappears immediately after a clean flush and power reset, internal sensors or gas valves may need replacement.
- Water dripping from the heater cabinet: If you spot water weeping from the metal casing seams, internal joints, or heat exchanger body, turn off the cold water supply valve immediately. Pinhole leaks caused by years of unaddressed mineral corrosion cannot be patched with tape or sealant and require professional component replacement.
- Frozen or corroded isolation valves: If the main shut-off levers or service port handles are seized with green corrosion and will not budge, never force them with a pipe wrench. Excessive torque can snap the underlying copper tubing inside your wall. A plumber can safely replace the valve assembly without damaging your home plumbing.
- Missing service valve kits: If your tankless unit was installed without service valves, a plumber must cut the copper or PEX supply lines and solder or crimp an isolation valve kit in place before you can perform routine maintenance.
Location also impacts the health of your water heating setup. When a tankless heater is installed in an unconditioned garage, utility shed, or basement, freezing drafts can chill standing water in the exposed copper pipes and split the metal coils. If your tankless unit sits in an unheated workspace, using the best electric heater for garage with thermostat can prevent internal pipes from freezing during severe winter months. In manufactured housing, utility closets are often tucked against exterior walls where cold air penetrates easily. Understanding the best heater for mobile home layouts helps you protect indoor utility rooms and keep your plumbing safe from seasonal cold snaps.
Performing a vinegar flush once every twelve months keeps your A.O. Smith tankless water heater operating at peak performance. By removing mineral scale before it hardens, you protect your heating coils, preserve full water pressure, and ensure your home enjoys uninterrupted hot water for years to come.





















