How to Safely Reset an AO Smith Water Heater
Getting an AO Smith tank running again usually means pressing the red safety reset button hidden behind the upper access panel. That simple fix only applies to electric tanks, because standard gas models do not have a push button at all. Before removing any metal covers or reaching inside, turning off the main power switch at the household breaker panel protects you from the dangerous 240-volt wiring inside.
Your next step depends on whether the unit runs on gas, which requires cycling the front temperature dial or resetting a power-vent switch instead. It also matters why the shutoff happened, such as a tripped breaker or water overheating from a damaged metal warming rod. Here is how to find the right switch, restart the tank safely, and tell if a broken part needs attention.
Shut Off Power At The Main Panel First
Before you touch any panel on your electric water heater, you must turn off the electrical supply at your home circuit breaker box. Electric water heaters do not run on ordinary 120-volt household current. They operate on a powerful 240-volt electrical circuit. Touching the wiring behind the access panel while that circuit is active can cause severe electrical shock, serious burns, or fatal injuries.
Head to your main electrical service panel to disconnect the power. Look for a double-pole switch, which is a wide breaker made of two switches joined together by a single plastic bar. This breaker should have a label such as "Water Heater" or "Hot Water." Firmly flip that switch into the OFF position. If the breaker switch is sitting in the center position between ON and OFF, it has already tripped. Push it all the way to OFF so the circuit is completely disengaged.
Do not rely on guessing whether the power is off. Use a non-contact voltage detector to verify that no electrical current flows through the wires before you reach inside the tank cabinet. Hold the tip of the voltage detector near the electrical cable entering the top of the tank. If the tool stays silent and does not flash, the power is safely shut down.
Take a quick look around the floor before you begin. Water heaters often sit in basements, utility closets, or garages where small leaks can pool on the concrete. Never work on an open electrical compartment while standing in damp spots or puddles. If you find standing water around the base of the tank, dry the entire area with towels and wear thick rubber-soled shoes before you loosen a single screw.
If your water heater sits in an uninsulated garage or utility shed, cold winter drafts can cause room temperatures to drop quickly, tempting owners to install a heater for a garage with a thermostat to keep the space warm. However, indoor room temperatures should never cause an internal tank reset switch to trip on its own, so electrical safety at the tank remains your absolute priority.
Push The Red Button Behind The Upper Panel
Electric AO Smith water heaters use a built-in safety cutoff switch, also called the high-limit cutoff. This switch protects your household plumbing by cutting off electrical current if the water inside the tank reaches dangerous temperatures. The switch features a small red button that physically pops outward when an overheat condition occurs. Resetting this button restores power to the upper and lower thermostats.
Follow these ordered steps to safely reset the button on an electric unit:
- Unscrew the upper access door: Grab a Phillips-head or flathead screwdriver and locate the upper metal cover plate on the side of your tank. Remove the two screws holding the panel in place. Place the screws in your pocket or on a nearby shelf so they do not roll away on the floor.
- Fold back the insulation: Behind the metal plate, you will see a thick piece of fiberglass insulation. Carefully fold this insulation back toward you. Try not to tear the insulation fibers, and avoid touching the material directly with bare skin if you have sensitive hands. Behind the insulation sits a clear plastic protective guard designed to shield you from internal wiring terminals.
- Locate the red reset button: Look through or gently lift the plastic safety cover. You will see the upper thermostat assembly mounted against the inner tank wall. Near the top of this assembly, right above the temperature adjustment dial, sits a small, round red button.
- Press the button until it clicks: Push the red button straight in with your thumb or the flat eraser end of a wooden pencil. If the safety switch was tripped, you will feel a firm mechanical snap and hear a distinct click as the internal contacts lock back together. If the button feels mushy, moves freely without resistance, or does not click, the switch may not have tripped in the first place, or the water inside the tank is still too hot to allow a reset.
- Reinstall the protective guards: Fold the plastic guard smoothly back into its original position over the wiring terminals. Press the fiberglass insulation flat over the opening. Place the metal access cover back onto the tank and tighten both screws securely. Never turn the electrical breaker back on while the access cover is off the tank.
- Restore electrical power: Walk back to your main breaker panel. Push the double-pole water heater switch firmly back to the ON position. Listen near the tank for a few seconds. You should hear a faint hum or the gentle sound of water warming as current flows to the metal warming rods inside the tank.
Give the tank at least forty-five to sixty minutes to heat the water. Resist the urge to turn on household faucets immediately. After an hour, open a hot water tap in your kitchen or bathroom sink. If the water flows warm and gradually gets hot, your reset was successful.
Reset Gas Models Using The Front Control Dial
If you own a natural gas or propane AO Smith water heater, you will not find an access panel with a red button. Gas models do not use 240-volt electrical heating rods, so they do not feature the same mechanical push-button cutoff found on electric tanks. Instead, resetting a gas model involves cycling the front control dial or restarting the electronic exhaust fan on power-vent units.
For standard gas water heaters that vent naturally through a metal chimney pipe, the gas control valve sits near the bottom front of the tank. This box contains the temperature dial, the pilot light window, and an internal thermal sensor. Follow these steps to clear a fault and relight the unit:
- Turn the control knob to OFF: Rotate the main temperature dial on the front of the gas valve clockwise until it points to OFF. This stops the flow of gas to both the main burner and the pilot assembly.
- Wait five full minutes: Let the combustion chamber vent completely. This waiting period allows any unburned gas lingering in the burner area to clear away through the exhaust flue, preventing sudden flare-ups when you relight the flame. If you smell gas near the floor, stop immediately, leave the house, and call your gas utility provider.
- Turn the knob to PILOT: Rotate the dial to the PILOT position and hold the knob down firmly. Holding the knob down forces gas through the small pilot supply tube.
- Ignite the flame: While holding the pilot knob down, press the clicker button on the front of the valve repeatedly until you see the pilot flame ignite through the sight glass. Keep holding the pilot knob down for thirty to sixty seconds after the flame appears. This gives the heat sensor enough time to warm up and verify the flame is stable.
- Switch back to your heat setting: Release the pilot knob. The flame should remain lit. Rotate the temperature dial to your desired warmth level, usually indicated by a "Hot" mark or a temperature setting around 120 degrees Fahrenheit.
Modern AO Smith gas water heaters feature a small status light on the front of the gas control valve. Watch this light closely after you set the dial. A single green flash every three seconds indicates normal operation and steady heating. If the light flashes in a repeated pattern, such as two, four, or five flashes in a row, consult the diagnostic chart on the tank label to identify the specific error code.
Power-vent gas models operate with an electric exhaust blower mounted on the top of the tank. These units plug into a standard 120-volt wall outlet. If your power-vent model stops running, reset it by unplugging the power cord from the wall outlet or flipping the rocker switch located on the fan housing to OFF. Wait forty-five seconds for the internal control board to clear its stored errors, then plug the unit back in. The blower fan will kick on first to purge the flue, followed by an automatic igniter firing the gas burner.
If your AO Smith unit is installed inside a manufactured house, make sure replacement parts and ventilation meet the specific codes required for that structure, similar to how installing an approved heater for a mobile home requires dedicated venting pathways.
Address The Underlying Cause Behind The Tripped Switch
A tripped reset button is a symptom of a larger issue, not the root problem. The safety switch trips only when water temperatures exceed roughly 170 to 180 degrees Fahrenheit, or when extreme electrical resistance overheats the thermostat bracket. Resetting the button once can restore hot water for your morning routine, but you need to know why the system shut down so it does not happen again.
A stuck thermostat is the most common reason for a popped reset switch on an electric water heater. Your tank uses two separate thermostats: one near the top of the tank and one near the bottom. When water cools, the thermostat contacts snap closed to send electricity to the heating element, which is the metal warming rod inside the tank. Once the water reaches the set temperature, the contacts snap open to stop the heat. Over time, electrical arcing can weld these contacts shut. When contacts weld shut, the heating rod runs non-stop, boiling the water until the red safety cutoff button pops to prevent the tank from bursting.
A burned-out or shorted heating element can also trigger the cutoff switch. As metal warming rods age, their protective outer metal sheath can split or corrode from mineral exposure. When this happens, electric current flows directly into the surrounding water. This electrical short creates severe localized heat and erratic electrical surges, tripping the safety reset button instantly.
Loose electrical wiring connections can cause false overheating. Because water heaters pull heavy electrical current, loose screw terminals create high electrical resistance. That resistance generates intense heat directly on the brass terminals of the thermostat bracket. Even if the water inside the tank is sitting at a safe 120 degrees Fahrenheit, the heat from the loose connection transfers straight into the high-limit switch, causing the red button to pop out.
Heavy mineral sediment at the bottom of the tank creates another common hazard. In areas with hard water, calcium and lime settle at the bottom of the tank, eventually burying the lower heating element under inches of solid mineral buildup. The trapped element cannot transfer its heat into the water efficiently. The metal warming rod overheats, the lower thermostat misreads the water temperature, and the entire thermal balance of the tank breaks down.
Learn to distinguish between a tripped circuit breaker in your home electrical box and a tripped red button on the tank itself. A tripped circuit breaker in your main electrical panel points to an electrical overload or a direct short circuit in the home wiring. A popped red reset button on the water heater points to excessive heat inside the tank or failing internal components.
Know When To Call A Licensed Professional
Pressing the reset button once is a reasonable homeowner fix. Resetting it twice in the same week is a warning sign that requires professional intervention. Pushing the button repeatedly while an internal part is failing can warp the tank shell, burn out internal wiring harnesses, or create a dangerous electrical fire behind the access door.
Shut down the power breaker and call a licensed plumber or qualified electrician if you encounter any of these warning signs:
- The button trips again immediately: If you push the red button, restore power at the breaker box, and hear the button pop back out within minutes or hours, stop trying to reset it. One of your thermostats or heating elements has suffered a complete electrical failure and must be replaced.
- Scorched, melted, or discolored wiring: When you open the upper access panel, inspect the wire insulation. If you spot blackened terminals, brittle insulation, melted plastic brackets, or smell a sharp burning electrical odor, do not touch anything. Leave the circuit breaker OFF and contact an electrician to replace the damaged wiring and controls.
- Water dripping inside the electrical compartment: If you find moisture, damp insulation, or rust around the thermostat mounting bracket, water is leaking through the tank gasket or the threaded bung of the heating element. Water touching high-voltage electrical connections creates an extreme shock hazard and shorts out the safety switch instantly.
- Scalding water or sputtering steam from faucets: If hot water coming from your sink or shower faucets spits steam, rattles the plumbing pipes, or measures dangerously hot to the touch, your tank is undergoing a runaway heating condition. Shut off both the electrical breaker and the cold water supply valve to the tank immediately.
- A leaking temperature and pressure relief valve: The brass valve with a small lever on the top or side of your tank is the temperature and pressure relief valve. If this valve discharges hot water onto the floor, the pressure or temperature inside the tank has reached extreme, unsafe levels.
Keep the age of your equipment in mind when deciding between repairs and replacement. Most storage tank water heaters provide a reliable service life of eight to twelve years. If your AO Smith water heater is more than a decade old and continually trips its safety switches, investing in replacement thermostats and heating elements often provides only a temporary fix. In that situation, replacing the aging tank with a new model is the safest, most dependable choice for your home.





















