How to Safely Restart a Rheem Gas Water Heater
Restarting a cold water heater requires turning the gas knob to OFF and waiting five full minutes for any trapped fuel to clear away. The exact method then depends on whether the tank uses a manual spark clicker or an electronic control box with an indicator light. Once the air clears, hold the knob down on PILOT while pressing the spark button until the small starter flame catches in the viewing window. Hold it for thirty seconds so the safety sensor warms up, let go, and turn the dial to your normal heat.
A couple of safety checks can alter these steps. Anyone who smells gas near the floor must leave the room immediately instead of trying to spark the flame. A tripped heat sensor can also lock the system down if the tank overheated earlier. Check the space around the heater first, then follow the steps below to bring your hot water back safely.
Sniff Test and Room Check: What to Verify Before Touching the Controls
Before you touch any dials on your water heater, you must confirm that the area around the tank is completely safe. Natural gas and propane are invisible, so utility companies add a strong chemical scent that smells like rotten eggs or sulfur. Take a moment to stand quietly next to the unit and breathe in through your nose.
Because propane is heavier than air, it sinks down and pools right along the floorboards. Natural gas is lighter than air and rises, but it can still collect in low pockets around the base of the tank. Lean down near the bottom metal skirt of the water heater and sniff carefully right at floor level.
- Check for sulfur or rotten-egg odors: If you detect even a slight smell of gas near the floor or around the pipes, do not touch the dials, do not strike a match, and do not flip any nearby light switches. Leave your home immediately and call your gas supplier or emergency services from outside.
- Clear away stored household items: Ensure there is at least a three-foot clear zone around the tank. Clear out cardboard boxes, laundry baskets, brooms, paints, cleaning sprays, and gasoline cans, which can catch fire or choke off the fresh air your heater needs.
- Look over the exhaust venting pipe: Look up at the metal pipe on top of the tank to make sure it is connected securely to the draft hood without any gaps, rust holes, or sagging sections.
- Inspect the floor for water puddles: Look for standing water around the base of the tank. A puddle can signal an internal tank leak or a leaking temperature and pressure relief valve, which must be addressed before relighting.
Step-by-Step Guide to Restarting a Rheem Gas Water Heater
Standard Rheem gas water heaters use a standing pilot system. This means a tiny starter flame stays burning continuously to light the larger main burner whenever your water cools down. If that flame blows out, you can safely restart it by following these ordered steps.
- Turn the gas control valve (the thermostat temperature dial and switch box) to the OFF position. Reason: This shuts off all gas to both the main burner ring and the starter nozzle so unburned fumes stop entering the sealed combustion box.
- Wait a full 10 minutes before touching any other controls. Reason: Trapped gas fumes need time to rise and vent harmlessly out through the chimney pipe, which prevents a sudden flare-up or pop when you spark the igniter.
- Remove the outer metal access door at the base of the tank. Reason: Taking off this outer metal panel reveals the sight glass (the small clear viewing window) so you can watch the burner area while leaving the inner sealed glass window in place.
- Turn the gas control knob from OFF to the PILOT position. Reason: Turning the knob to this dedicated mark aligns the internal valve passages so fuel flows strictly to the starter nozzle and cannot reach the main burner.
- Press down firmly on the PILOT knob and hold it down completely. Reason: Pushing down manually overrides the internal safety magnet, forcing a small trickle of gas to travel down the thin supply line directly to the starter tip.
- Press the push-button spark clicker repeatedly while keeping the PILOT knob held down. Reason: Every firm click strikes a static electric spark across the gap next to the pilot nozzle to catch the flowing gas.
- Peer through the small clear viewing window to verify the flame is burning. Reason: Looking through the glass confirms that the gas has actually caught fire so you do not keep pumping unburned fuel into the combustion chamber.
- Continue holding the PILOT knob down firmly for 30 to 60 seconds after the flame appears. Reason: The small starter flame must heat the thermocouple (the safety heat sensor rod) until it produces enough millivolts of electricity to keep the gas valve open on its own.
- Release the PILOT knob slowly and confirm the small starter flame stays lit. Reason: This verifies that the safety heat sensor rod is hot enough to hold the magnetic safety valve open without your thumb pressing the button.
- Turn the gas control knob smoothly from PILOT to the ON position. Reason: Switching to ON opens the primary gas port, allowing the thermostat to send fuel to the main burner ring when the water requires heating.
- Reinstall the outer metal access door and adjust the temperature dial to your desired warmth. Reason: Putting the outer door back on shields the flame from room drafts, and setting the dial commands the main burner to roar to life with a steady blue glow.
How to Restart Rheem Models with an Electronic Igniter and Status Light
Modern Rheem gas water heaters often feature an electronic thermostat control box with an LED status light. These units do not need household wall plugs or batteries. Instead, they generate their own tiny electrical charge from the heat of the starter flame to run an internal processor and flash diagnostic signals.
To restart one of these newer electronic units, first turn the temperature dial counterclockwise to the OFF position. Wait 10 full minutes to ensure any residual fuel escapes up the draft hood. Once the waiting period ends, remove the outer metal door so you can see the small clear viewing window at the bottom of the heater.
Rotate the dial clockwise to the PILOT position, then press and hold the dial down into the box. While keeping the dial pressed down, repeatedly click the push-button spark clicker once every two seconds. Watch the small green light on the front of the thermostat box. You should see it begin to blink once the safety heat sensor rod gets hot enough to power the electronics.
Keep holding the dial down until the green light gives a steady, single heartbeat flash once every three seconds. This heartbeat flash is the universal Rheem signal that the unit is operating normally and holding a stable flame. Release the dial, snap the outer metal door back onto the tank, and rotate the dial to your desired temperature mark, such as the Hot setting.
Why the Pilot Flame Goes Out Immediately and How to Clear It
If your starter flame lights up while you hold down the button but snuffs out the moment you let go, your water heater is shutting down for safety. The unit believes there is a fire risk or cannot verify that a safe flame exists. Several common issues cause this cycle.
The most frequent culprit is a dirty safety heat sensor rod. Over months and years of constant burning, carbon soot, white mineral dust, and oxidation coat the metal rod. This coating acts like an insulating blanket, preventing the small starter flame from warming the metal to the required temperature. Without that heat, the sensor cannot create the small electrical current needed to hold the gas valve open, causing it to snap shut.
Trapped air in the fuel line also causes instant flame loss. If your gas service was shut off recently, or if the tank sat idle for months, the narrow copper supply pipe fills with regular room air. You may need to hold down the PILOT knob for two or three full minutes to bleed out the trapped air before pure gas reaches the tip and produces a steady, stable flame.
Drafty rooms can cause sudden gusts of air that blow out a fragile starter flame before the sensor rod heats up. If your water heater sits in a chilly garage or workshop, pairing your setup with the best electric heater for garage with thermostat control can help eliminate cold floor-level drafts that destabilize utility burners. Similarly, if your water heater is tucked into a tight manufactured home closet, combustion airflow is very sensitive, which is why owners also evaluate the best heater for mobile home setups to balance whole-house ventilation.
Another common cause is a clogged air intake screen at the base of the tank. Rheem water heaters draw fresh air from underneath the burner through a fine flame arrestor screen. When this metal mesh fills with household lint, dryer fuzz, or pet hair, the burner starves for oxygen. The flame lifts off the burner, flickers wildly, and trips the thermal cutoff switch located near the burner door wires. If this safety switch trips, gently push the small button in its center to reset it after clearing dust away from the bottom base.
Warning Signs to Stop Immediately and Call a Licensed Plumber
Relighting a water heater is a routine homeowner task, but certain mechanical failures create severe hazards. If you observe any of the warning signs below, stop trying to restart the unit, turn the gas valve to OFF, shut off the gas supply line valve, and call a professional.
- A persistent rotten-egg gas smell: Any odor of fuel that stays in the room after your 10-minute waiting period, or grows stronger as you work, indicates a leaking fitting or cracked control box.
- Heavy soot or black scorching around the door: Black soot marks on the outside of the water heater, or around the metal draft hood on top, show that the fuel is burning incompletely and producing toxic carbon monoxide.
- A yellow, rolling burner flame: Healthy natural gas and propane flames burn with a sharp, vibrant blue cone. A lazy, floppy yellow or orange flame means the burner is starving for air or choked with soot.
- Loud booming or delayed ignition: If you hear a loud bang or whoosh that rattles the tank when the main burner catches, fuel is pooling before it ignites.
- Water dripping into the combustion box: If water is sizzling on top of the burner or pooling under the flame, the inner glass-lined steel tank has failed and the entire water heater must be replaced.
- Repeating error codes that resist resetting: If your electronic status light blinks four, five, or seven times in a sequence, an internal sensor or safety switch has failed and requires professional diagnostic tools.
FAQs
How long after restarting will hot water be ready?
Most standard Rheem gas water heaters take about 30 to 45 minutes to heat a full 40-gallon or 50-gallon tank of cold water. Recovery time depends on the temperature of the incoming ground water and the tank capacity. You will hear the main burner roaring quietly while it works, and the top hot water pipe leaving the tank will feel warm to the touch within 20 minutes.
Can I light my Rheem water heater with a match if the clicker fails?
You should never use a match, candle, or handheld lighter on a modern Rheem water heater. These units feature a sealed combustion chamber with a glued airtight viewing window designed to prevent flammable fumes in the room from catching fire. Opening the sealed inner burner door breaks this critical gasket and voids the safety protection of the system. If the built-in clicker fails to produce a spark, replace the igniter assembly rather than lighting the chamber manually.
Why does the pilot flame stay lit while I hold the knob but dies when I let go?
This problem almost always points to a problem with the safety heat sensor rod, also called the thermocouple or thermopile. The sensor rod must sit directly in the flame to heat up and generate a tiny electrical signal that keeps the gas valve open. If the rod is dirty, bent away from the flame path, or worn out internally, the safety valve assumes the fire went out and snaps shut the moment you release the button.
What temperature setting should I choose on the dial after restarting?
Set the temperature dial to the Hot mark, which corresponds to roughly 120 degrees Fahrenheit on standard Rheem gas control valves. This temperature supplies plenty of comfortable hot water for showers and dishwashers while protecting children and elderly family members from accidental scalding. Setting the dial higher increases energy costs and speeds up mineral scale buildup along the bottom of the water tank.
Related guides: how to restart a rheem water heater and best rheem gas water heater and best rheem pilotless gas water heater.





















