Bestwinterproducts.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

How to Turn on a Resideo Water Heater Safely

Prime for Young Adults: check your eligibility on Amazon

Set the knob to pilot and spark it. Switch the main dial to Pilot, press and hold the knob down, and firmly click the spark button until the tiny indicator light blinks. Keep holding the knob down for about thirty seconds so the heat sensor can warm up and keep the gas flowing, let go, and then turn the dial to your normal temperature.

A few everyday details can change how quickly the burner fires up. The gas valve on your supply pipe must sit completely open, parallel to the line. If the heater was off for weeks, trapped air in the pipe may require a few extra button presses to bleed out before the flame catches. Some models use that push button, while others spark on their own. Walk through the safe steps below to get your tank running properly.

The Short Version

  • Turn the gas control knob on the front of the tank to OFF, wait at least five minutes for any leftover gas to clear completely, and verify that there is no rotten egg smell near the floor.
  • Rotate the control knob to PILOT, push and hold the knob down firmly to start the gas flow, and repeatedly press the push-button sparker until the pilot flame catches.
  • Keep holding the knob down for 30 to 60 seconds so the heat sensor rod warms up, and watch for the small indicator light on the control box to begin flashing a steady heartbeat pattern.
  • Release the knob smoothly, confirm that the indicator light keeps blinking, and turn the temperature dial to your desired heat setting to fire up the main burner.

Safety First: Checking for Gas Before You Touch the Controls

Working around any gas appliance calls for caution. Natural gas and propane burn cleanly, but an unlit gas leak trapped in an enclosed utility closet or basement creates a real hazard. Gas utility providers add a chemical called mercaptan to fuel lines, which gives escaping gas a distinct smell like rotten eggs or sulfur. Before you reach for any buttons or dials on your water heater, take two minutes to inspect the space around the unit.

Propane is heavier than air and sinks to the floor, while natural gas rises toward the ceiling. Dip down near the base of the tank to sniff around the burner door, then check at chest height. If you notice even a faint sulfur smell, do not push any buttons, do not strike matches, and do not flip any light switches on or off. An electric light switch can throw a tiny internal spark capable of igniting airborne gas. If you smell gas, step outside your home immediately, leave the door open behind you to vent the room, and call your local gas utility company or fire department from a safe distance.

If the air smells clean, check the physical space around the tank. Clear away laundry baskets, cardboard storage boxes, brooms, paints, and cleaning chemicals. A water heater needs a three-foot safety buffer on all sides to pull in fresh combustion air and prevent accidental fires. Water heaters installed in tight spaces, such as utility closets designed for compact living spaces like those described in our guide to the best heater for mobile home setups, rely heavily on clean air intake grilles near the floor. Vacuum away any heavy dust bunnies, lint, or pet hair gathered around the base of the tank before you try to start the burner.

Finally, trace the rigid metal or flexible yellow gas line that runs from the wall or ceiling down to the control box on the front of the tank. Look for the manual gas shutoff valve, which is usually a small lever handle located on the pipe. The handle must point directly in line with the pipe to let gas through. If the handle sits perpendicular to the pipe, forming a cross or T-shape, the gas supply is currently shut off. Turn the handle a quarter turn so it runs parallel with the gas pipe before moving to the controls.

How to Light the Pilot and Turn On the Burner Step by Step

The Resideo control box on the front of your water heater manages gas flow, pilot ignition, and water temperature. It uses a modern sealed combustion chamber, meaning the pilot flame and burner sit behind a thick metal door with a small glass viewing window. You never need to remove this door or use matches. Follow these steps in order to start your heater safely.

  1. Shut off the gas control and wait. Turn the main temperature dial on the control box fully counterclockwise to the lowest setting, then turn the gas control knob to OFF. Wait at least five full minutes. This waiting period is critical because it allows any unburned gas that gathered inside the burner chamber to escape up the exhaust chimney.
  2. Set the control knob to PILOT. Rotate the gas control knob clockwise until the word PILOT aligns with the indicator mark on the box housing.
  3. Depress the knob to open the pilot channel. Push down firmly on the control knob and hold it down. This physical pressure bypasses the internal safety magnet and manually forces a small trickle of gas out through the pilot nozzle inside the combustion chamber.
  4. Click the push-button sparker. While keeping the knob pressed down with one hand, use your other hand to press the push-button sparker like the one on a gas grill. Press it firmly every two to three seconds. You will hear a sharp mechanical snap with each press. Peek through the small glass sight window located near the bottom of the tank, just below the control box. You should see a tiny electric spark jump across the pilot gap, followed by a soft blue flame catching on the burner tip. If your tank sits in a dark corner, shining a flashlight at an angle against the glass helps you spot the small flame.
  5. Hold the knob down to heat the sensor. Once you spot the small blue pilot flame, do not release the gas control knob. Continue pressing it down firmly for 30 to 60 seconds. The pilot flame must heat the heat sensor rod that detects the flame and unlocks gas flow. This sensor rod converts heat into a tiny electrical charge. If you let go of the knob before the sensor gets hot enough, the safety system thinks the flame went out and instantly snaps the gas valve shut.
  6. Watch for the indicator light. Keep holding the knob down while looking at the small indicator light on the control box. Within 30 to 60 seconds, this light should begin flashing a steady, rhythmic green pulse. The light confirms that the sensor rod is hot, generating sufficient voltage, and that the internal brain of the valve is active.
  7. Release the knob and engage the burner. Gently take your hand off the control knob. The knob should pop up slightly, and the pilot flame should stay lit. The indicator light will keep blinking every few seconds. Now, rotate the main temperature dial clockwise away from PILOT to your chosen heat setting, such as Warm or the manufacturer recommended Hot setting. You will hear a distinct click inside the box, followed by a soft whoosh as gas rushes into the main burner tray and ignites into a ring of steady blue fire.

What the Blinking Status Light on the Resideo Box Means

Unlike older mechanical water heaters that used purely manual dials, the Resideo gas valve contains a small electronic monitor. It does not use household wall power and has no battery compartment. Instead, the heat sensor rod sitting directly in the pilot flame generates small amounts of electricity through thermal energy. This self-powered design allows the small indicator light on the control box to give you clear feedback on how the heater is running.

Under normal conditions, once the pilot is lit and stable, the status light flashes once every three seconds. Many plumbers refer to this as the heartbeat flash. It tells you that the sensor rod is producing proper voltage, the gas valve is safe to operate, and the temperature sensors inside the tank are reading correctly. As long as you see this slow, steady pulse, your water heater is functioning properly.

If the light flashes rapidly or pulses in a specific sequence with pauses in between, the control box is signaling a diagnostic trouble code. For example, two flashes followed by a pause often indicates a weak electrical signal from the heat sensor rod, meaning the rod is either loose, dirty, or failing to sit directly in the flame path. Four flashes usually indicates that the high-temperature safety switch opened because water inside the tank reached unsafe limits. You do not need to memorize these sequences. Resideo prints a diagnostic flash chart right on the side or front label of the control box. Count the flashes between pauses and check that label to see what the control box is reporting.

Why the Pilot Flame Drops Out When You Let Go of the Knob

The most common frustration homeowners run into when lighting a water heater is watching the pilot light up perfectly, only to vanish the exact second they let go of the control knob. This happens because the internal safety magnet requires an electrical current to hold the gas port open. If anything interrupts that current, the spring-loaded valve snaps closed to stop unburned gas from leaking into your home. Several everyday issues can cause this drop out.

The simplest cause is releasing the knob too early. The heat sensor rod needs sustained, direct heat to build up its electrical charge. If you let go after only ten seconds, the metal rod remains too cool, and the safety valve closes instantly. Always give the knob a full 60 seconds of steady downward pressure after you see the flame ignite before easing your fingers off.

Another frequent cause is air sitting inside the fuel supply line. If your gas service was briefly turned off, or if the water heater sat unused for months, the gas pipe fills with ambient air. When you depress the pilot knob, you might push pure air or a weak mixture of air and gas out of the nozzle for the first minute or two. The push-button sparker might ignite a weak flame that sputters out quickly because the fuel stream is inconsistent. In this situation, holding the knob down in the PILOT position for an extra minute purges the lingering air from the pipe until fresh, rich gas reaches the pilot head.

Physical soot buildup can also block heat transfer. Over months of use, a fine layer of black carbon dust can coat the tip of the heat sensor rod. Carbon acts as an insulator, preventing the heat of the flame from warming the internal metals of the sensor. If your water heater sits in a dusty basement or an unconditioned garage where cold drafts pull heat away from the tank base, keeping the burner chamber warm enough to establish an initial current can take longer. Homeowners using the best electric heater for garage with thermostat setups nearby often find that keeping the room above freezing helps prevent heavy condensation and draft issues around their utility appliances, but you must ensure external fans never blow air directly into the bottom vents of the water heater.

Finally, a damaged thermal cutoff switch can kill the flame instantly. Modern sealed burner chambers feature a small thermal switch near the burner door designed to break the electrical circuit if the combustion chamber gets too hot, such as when an intake air filter becomes fully clogged with lint. If that safety switch has tripped, the circuit stays broken, and no amount of holding down the knob will keep the pilot lit once released.

Clear Signs to Stop Trying and Call a Professional

Lighting a water heater pilot is a straightforward maintenance task, but there is a clear boundary between routine operation and an unsafe mechanical problem. If you encounter any of the following warning signs, stop attempting to light the heater, turn the gas valve to OFF, and reach out to a licensed plumber or gas technician:

  • A strong or continuing gas smell: If the odor of sulfur or rotten eggs does not clear after ten minutes, or if it grows stronger while you attempt to light the pilot, leave the room immediately and shut off the main gas supply line if you can do so safely from an outside valve.
  • No spark from the push-button mechanism: If clicking the push-button sparker produces no visible spark in the viewing window and no sharp snapping sound, the internal wire may be disconnected, cracked, or grounded out against the tank frame.
  • Repeated flame failure after four attempts: If you have held the knob down for a full minute across three or four separate tries and the pilot consistently dies the moment you release the knob, the heat sensor rod or the control box itself has likely failed.
  • Soot, scorch marks, or warped metal: Look at the lower combustion access door and the outer jacket of the tank. If you see black soot streaks, blistered paint, or heat discoloration, the burner is not venting properly and could produce dangerous carbon monoxide gas.
  • Water pooling inside the burner compartment: If you shine a light through the sight glass and see standing water or heavy dripping directly onto the burner tray, the inner glass-lined water tank has developed a leak, and the entire water heater must be replaced.

FAQs

How long should I hold the knob down after the pilot flame lights?

Hold the control knob down for 30 to 60 seconds after you see the pilot flame ignite in the viewing glass. This gives the heat sensor rod enough time to heat up and produce the electrical current needed to hold the internal gas valve open. Releasing the knob before 30 seconds almost always causes the flame to extinguish immediately.

Can I light a Resideo water heater pilot with a match or long lighter?

No, you should never attempt to light a modern Resideo water heater using a match or a handheld barbecue lighter. These units feature a sealed combustion chamber designed to keep fuel vapors safely contained behind a sealed metal door and gasket. Opening this door voids the safety seal, exposes you to sudden flare-ups, and can damage the combustion chamber components.

What should I do if the push-button sparker fails to make a spark?

First, inspect the thin wire running from behind the push-button sparker down into the burner door to make sure it is firmly plugged into the bottom of the button terminal. If the wire is plugged in securely but you still see no spark through the glass when clicking firmly, the piezo mechanism or ceramic electrode tip is damaged and requires replacement by a qualified technician.

What temperature setting should I choose after the burner turns on?

Turn the dial to the Hot setting or roughly 120 degrees Fahrenheit, which is the standard mark recommended by manufacturers and safety agencies. This setting provides plenty of hot water for household showers and appliances while preventing accidental scalds, especially for young children and older adults. Setting the dial higher increases energy costs and raises the risk of rapid tank mineral buildup.

4
1 ratings
John Deutsch
WRITTEN BY
John Deutsch
John is a editor based in New York, known for his expertise in finance and economics. With more than 15 years of experience, he provides insightful articles on personal finance, investment strategies, and economic trends.