Bestwinterproducts.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

Is There Copper in a Water Heater?

Prime for Young Adults: check your eligibility on Amazon

A heavy tank sits disconnected on the garage floor, leaking a puddle of brown water while someone eyes the metal shell for valuable scrap. The truth is that yes, there is copper inside, but standard tank units hold very little of it. The bulk of that heavy cylinder is plain steel, with copper limited to thin internal wires, small brass fittings, and the heating elements that warm the water.

The exact haul depends on the design resting on the floor. Compact tankless units usually carry a solid copper heat exchanger, which is the metal coil that transfers warmth to the water. In contrast, regular electric or gas storage tanks yield only a few pounds of copper after hours of cutting through sharp sheet metal and sticky fiberglass insulation. Here is where the metal hides, what it weighs, and how to tell if stripping the heater is worth the sweat.

Do Not Expect a Solid Copper Tank Under the Outer Shell

Many homeowners assume an old water heater is a giant container of solid copper. That belief usually comes from seeing copper plumbing lines soldered directly to the top fittings, or from hearing stories about antique plumbing equipment. Modern storage water heaters are built differently. Almost every standard residential tank built over the last fifty years is made almost entirely of carbon steel.

Inside the outer painted jacket sits a thick steel pressure vessel. Manufacturers coat the inside of this vessel with a thin layer of porcelain enamel glass to protect the raw metal from rust. Steel gives the unit the physical strength it needs to hold forty or fifty gallons of water under continuous pressure, which often reaches fifty to eighty pounds per square inch. Solid copper of that thickness would be far too expensive for everyday residential manufacturing.

You can confirm this yourself using a simple refrigerator magnet. Touch the magnet against the outer casing, and it will snap firmly against the surface. Copper is non-magnetic, while steel contains iron that grabs magnets instantly. Even if you peeled away the outer jacket and the layer of insulation, the magnet would grab the heavy inner water vessel just as hard.

Very rare exceptions exist from decades past. Between the 1920s and the early 1950s, a few manufacturers built residential tanks from solid copper or bronze alloys for areas with aggressive well water that quickly corroded steel. Today, finding one of these vintage tanks in a basement is rare. If your water heater was installed in the last several decades, the tank itself is steel scrap.

An empty 40-gallon or 50-gallon tank usually weighs between 100 and 150 pounds. Steel accounts for roughly 95 percent of that total weight. Scrap yards classify the main vessel as light iron or shred steel, which pays a modest rate per ton rather than the high price per pound that copper brings.

Check the Heating Elements, Wiring, and Brass Connectors First

While the main vessel is steel, copper definitely hides in specific components around the unit. If you plan to salvage metal, these smaller pieces are where your actual scrap value sits.

Electric units hold copper inside their heating elements. A heating element is an electric rod inside the tank that gets hot when electricity flows through it. Most electric tanks have an upper and lower element screwed or bolted into the side. Many of these rods use a copper outer sheath to transfer heat rapidly into the water. Sometimes the copper is plated with nickel to resist mineral buildup, giving it a dull silver appearance. You can verify the metal beneath the plating by making a shallow scratch with a metal file. If bright reddish-orange metal shines through, the sheath is copper. Each pair of elements yields about one to two pounds of mixed copper material.

Short electrical wires sit behind the side access panels. When you remove the metal covers over the thermostats, you will find insulated jumper wires connecting the controls. Snipping them out with wire cutters takes seconds, yielding a few ounces of clean insulated copper wire.

Threaded brass fittings are another reliable spot for scrap metal. Brass fittings are threaded metal connectors made partly of copper, typically containing roughly 60 to 70 percent pure copper mixed with zinc. Look at the temperature and pressure relief valve mounted near the top of the tank. The body of this valve is almost always cast brass or bronze. The bottom drain valve is also solid brass on older units and higher-grade models, though budget units often use plastic.

Skip the anode rod. An anode rod is a metal core rod that prevents tank rust by sacrificing its own metal to corrosive minerals. It hangs from a hex bolt on top of the tank. While it looks like a heavy copper pipe, it is actually aluminum, magnesium, or zinc over a steel wire core. Scrap yards purchase anode rods as low-grade mixed scrap, not copper.

Compare Storage Tanks Against Tankless Units Before You Haul

The type of water heater you have completely changes the scrap metal equation. Traditional storage tanks are mostly steel with small copper accents, but tankless models are a completely different animal.

Tankless water heaters do not store dozens of gallons of standing water. Instead, they heat water instantly as it moves through the machine. To make this instant heating work, the burner or electric elements transfer intense heat directly into a heat exchanger. A heat exchanger is a metal coil that transfers heat to water as the liquid flows past.

Because copper conducts heat faster than almost any other common metal, manufacturers use thick, pure copper to construct these internal heat coils. In a whole-house gas tankless unit, the copper heat exchanger forms a dense, finned block that sits right above the gas burners. That single copper assembly often weighs between 5 and 15 pounds on its own. It is high-grade scrap copper without heavy insulation glued to it.

Inside an electric tankless unit, you will often find solid copper heating chambers rather than a single coil. These heavy copper canisters surround the electric rods and channel water tightly around the heat source. The copper in these chambers is thick, clean, and easily unbolted from the outer housing.

When you compare the two styles, a small 20-pound tankless unit can yield more scrap copper than a 150-pound storage tank. The tankless unit is also much easier to transport in a car trunk and takes ten minutes to take apart with basic hand tools. If you are dismantling scrap appliances in your workshop during freezing weather, working next to a steady heater for a garage with a thermostat makes handling cold wrenches and tiny brass screws far more comfortable.

Weigh Your Labor and Scrap Yard Prices Before Cutting Metal

Many people want to tear apart a standard water heater expecting a big cash payout at the scrap yard. Before you grab power tools and start cutting into the tank, look closely at the labor, mess, and expense involved.

Standard storage tanks are insulated with expanding polyurethane foam. Manufacturers inject this chemical foam between the outer metal shell and the inner steel pressure tank. Over years of heating cycles, the foam bakes onto the steel surfaces. If you slice open the outer jacket with a saw, you will uncover inches of sticky foam that breaks into thousands of tiny yellow particles.

This foam creates an enormous mess. It clings to clothing, irritates skin, and generates dust that requires a respirator mask. Once stripped, you must still scrape sticky residue off the metal to earn clean scrap pricing. Otherwise, yards downgrade dirty metal to the lowest scrap tier.

Tool wear also eats your profit. Cutting heavy steel quickly dulls or snaps metal-cutting saw blades. If you spend fifteen dollars on replacement blades to pull eight dollars worth of copper and brass, you lose money on the project.

The most profitable approach for a standard tank is a partial teardown. Use ordinary hand tools to remove the brass drain valve, the brass relief valve, the electric heating elements, and any copper pipe stubs on top. Leave the heavy steel cylinder completely intact. Sell your copper and brass in separate buckets for premium prices, then drop the whole steel tank off at the yard as shred iron. That method gives you most of the cash value with zero foam mess and zero broken blades.

Follow These Safety Steps Before Draining or Stripping Any Unit

Tearing down a plumbing appliance presents real hazards, including electric shocks, gas leaks, scalding water, and heavy lifting injuries. Always follow a strict, ordered process before you put a single tool on the metal.

  1. Shut off all power and fuel supplies. For electric heaters, turn off the dedicated breaker at your main electrical panel. Remove the front access plate and use a non-contact voltage detector to confirm no terminals carry current. For gas units, turn the control dial off, shut the gas supply valve on the pipe, and unthread the flexible gas line with two wrenches.
  2. Isolate and drain the water completely. Turn the cold water shutoff valve above the heater clockwise until it stops. Connect a garden hose to the bottom drain valve and route it to a drain. Lift the relief valve lever near the top to break the vacuum. Let all water drain out. If the unit ran recently, wait a few hours so the water cools before draining.
  3. Cut external copper pipes cleanly. Use a small tube cutter or a hand hacksaw to sever the copper water lines a few inches above the tank connections. Keep these short copper pipe sections separate from the steel tank, because clean copper plumbing pipe qualifies for the highest scrap category at recycling facilities.
  4. Unscrew accessible brass and copper parts. Use a pipe wrench to back out the brass relief valve from the tank wall. Grip the bottom drain valve with your wrench and unthread it counterclockwise. On electric units, remove the side inspection covers and unscrew the heating elements using an element socket wrench. Cut the short copper wires that connect the upper and lower thermostats.
  5. Sort your metals into distinct containers. Scrap yards operate on strict material grades. Keep your clean copper tubing, your insulated copper wire, your brass valves, and your steel parts in separate buckets. If you toss brass fittings or steel bolts into a container of clean copper, the scrap yard worker will grade the entire container down to the cheapest metal inside it.
  6. Haul the heavy steel vessel safely. Old water heaters collect heavy mineral sediment at the bottom of the tank over years of service. Even after all water drains out, a tank can hold thirty to fifty pounds of wet calcium and sand settled at the base. Use an appliance dolly with secure straps to roll the tank out, and always lift with your legs to protect your back.

FAQs

Can you find solid copper water heaters in homes today?

Solid copper tanks are almost non-existent in modern residential construction. While a few luxury manufacturers made copper-alloy tanks prior to the 1950s, modern building codes and material costs shifted the market entirely to porcelain-lined steel. Unless you are removing an antique appliance from an untouched mid-century estate, your standard storage tank is made of carbon steel.

How can I verify if a heating element is copper or stainless steel?

You can verify the metal by scratching the outer surface of the element with a metal file or sandpaper. Many copper elements feature a thin nickel coating to protect against minerals, making them look silver on the outside. A light scratch through this outer coating will reveal reddish-orange copper if it is present. If the metal remains bright silver all the way through, the element is stainless steel.

Do scrap yards accept water heaters that are still fully assembled?

Yes, scrap yards routinely accept intact water heaters as light iron or shred steel. You do not need to tear the appliance apart to sell it, though you will receive the lower mixed-metal rate for the total weight of the unit. Scrap yards prefer that you drain all water out beforehand, because excess water adds false weight and creates hazards in metal shredders.

Is the anode rod inside a water heater worth scrap money?

The anode rod has very little scrap value compared to copper or brass. Manufacturers build anode rods by casting aluminum, magnesium, or zinc around a central steel support wire. Because these metals are corroded and bonded to a steel core, recycling facilities classify them as low-grade mixed metal, which yields only pennies per pound.

4.7
3 ratings
Michelle Collins
WRITTEN BY
Michelle Collins
Michelle Collins, a female editor based in Boston, is a beacon for affordability in winter and outdoor products. With a decade of experience, she encourages readers to make smart, budget-friendly choices.