Bestwinterproducts.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

How Often Should You Flush an AO Smith Water Heater?

Prime for Young Adults: check your eligibility on Amazon

Many people believe a water heater only needs attention when hot water runs out or a pipe leaks. That assumption usually causes noisy tanks and early breakdowns, because a standard storage tank actually needs to be cleared out once every year. Tankless units follow a similar schedule, needing a thorough rinse every twelve months to keep narrow water lines clear of crusty mineral buildup.

A few household conditions can shorten that timeline. Homes with hard tap water collect loose sand and mineral grit much faster, which often means servicing a tankless unit every six months. Running lots of laundry and daily showers also speeds up the debris gathering at the base of a storage heater. Learning when to step in protects the inner tank lining and keeps water temperatures steady all year long.

The Short Version

  • Standard storage tanks: AO Smith recommends flushing your tank water heater once every year to clear out mineral grit and keep heating costs low.
  • Hard water areas: If your home has well water or heavy mineral content, flush the tank every six months to prevent the buildup from turning into hard rock.
  • Tankless units: Clean and flush an AO Smith tankless heater once every 12 months through descaling (clearing hard mineral crust with vinegar), or every six months in hard water zones.
  • Neglected tanks: If your heater has not been flushed in eight years or more, avoid a full drain without a plumber, because clearing old buildup can uncover tank rust holes.

Recommended AO Smith Flush Schedules for Tank and Tankless Units

Water entering your home carries microscopic minerals like calcium and magnesium. When that water sits inside your heater and warms up, those minerals separate from the liquid. They sink straight to the bottom of the tank. Over several months, this loose sand and mineral grit, known as sediment, forms a thick blanket across the base of the tank.

For a standard tank storage water heater, AO Smith recommends draining and flushing the tank once every 12 months. This yearly schedule keeps the loose grit from settling into a solid layer. If you stick to this annual habit, a quick flush takes less than half an hour and stops the minerals from causing permanent damage.

Water hardness changes this timeline dramatically. In regions with hard water, minerals drop out of the water twice as fast. Homes that pull water from private wells or municipal systems with high mineral content often accumulate inches of scale in less than a year. If you live in one of these areas, flush your AO Smith tank every six months. Doing it in the spring and fall keeps the bottom clean and prevents heating elements from burning out early.

Tankless AO Smith units require a different approach. Tankless models do not hold 40 or 50 gallons of standing water. Instead, they force cold water through small, narrow copper heat exchanger pipes that get intensely hot. Minerals bake directly onto the interior walls of these narrow passages. To fix this, tankless heaters require descaling (clearing hard mineral crust with vinegar) once every year using a small pump and a bucket of white vinegar. In hard water areas, descale your tankless unit every six months to prevent the heat exchanger from choking completely.

Household hot water demand also plays a role. A 50-gallon tank supplying a busy household of five people processes thousands of gallons of fresh, mineral-rich water every month. That unit collects debris far faster than a 30-gallon tank in a home with only one or two residents. The more water your household runs through the system, the more frequently you should connect a hose to clear out the tank floor.

Warning Signs That Your Water Heater Needs Flushing Now

You do not have to wait for your 2026 maintenance calendar if your AO Smith heater shows clear signs of distress. Mineral buildup creates distinct symptoms that tell you the tank floor is covered in grit.

  • Popping or rumbling noises: As water heats beneath a heavy layer of mineral grit, it gets trapped against the bottom metal plate. The trapped water turns into steam pockets that violently bubble up through the muck. This creates loud knocking, kettle boiling, or popping sounds whenever the burner fires.
  • Hot water runs out quickly: A thick layer of mineral crust acts like an insulated barrier. It blocks heat from reaching the water efficiently, which means your water heater takes longer to recover and runs out of hot water halfway through a normal shower.
  • Cloudy or gritty tap water: If your hot water looks cloudy, has a slight yellow tint, or leaves sandy white specks in your sink aerators, the sediment layer has grown tall enough to enter your home hot water pipes.
  • Higher electric or gas utility bills: When heat cannot pass freely through the base of the tank, the burner or electric heating elements must stay on much longer to reach your set temperature. This wasted energy shows up directly on your monthly bill.
  • Drips around the drain valve: Loose grit can get caught in the rubber seal of the drain valve (the bottom spigot for attaching a garden hose), creating persistent drips on your utility room floor.

Step-by-Step Guide to Flushing an AO Smith Tank Water Heater

Flushing an AO Smith tank is a straightforward job that requires only a standard garden hose, a flathead screwdriver or channel locks, and a safe place to dump hot water. Follow these steps in order to protect your unit and prevent accidental burns.

  1. Turn off the heat source: Never drain an active heater. For an electric AO Smith model, switch off the dedicated circuit breaker in your electrical panel. For a gas model, turn the temperature control knob on the gas valve to the "PILOT" position. If electric heating elements are left powered while the tank empties, the air will cause them to burn out in less than a minute.
  2. Attach your garden hose: Locate the drain valve near the bottom of the heater. Screw one end of a garden hose tightly onto the threaded brass or plastic spigot. Make sure the rubber washer inside the hose fitting is seated flat so hot water does not spray across your shoes.
  3. Direct the hose to a safe drainage spot: Run the open end of the hose to a basement floor drain, an outdoor driveway, or a utility sink. If you run the hose outdoors, keep children and pets far away. The first blast of water coming out of the tank can reach 120 to 140 degrees Fahrenheit and will scald bare skin instantly.
  4. Relieve the internal vacuum: Shut off the cold water shutoff valve located on the pipe entering the top right of the tank. Next, walk to your highest bathroom sink and turn on the hot water tap. Leaving this faucet open lets air into the plumbing system so the tank can drain freely without creating a vacuum lock.
  5. Open the bottom drain valve: Use your hand, a flathead screwdriver, or pliers to open the bottom spigot. Water will begin flowing through the hose. Watch the drainage carefully. You will likely see discolored water carrying sandy white, brown, or black flakes. Let it run until the tank is completely empty.
  6. Blast out the stubborn sediment: Once the water stops flowing, open the cold water supply valve at the top of the tank for one minute while the drain valve remains wide open. The pressurized burst of incoming cold water stirs up loose sand and mineral grit resting on the tank floor and forces it out through the hose. Turn the cold water off, let it drain, and repeat this quick blast until the runoff water comes out crystal clear.
  7. Disconnect the hose and close the valve: Close the bottom drain valve completely and unscrew your garden hose. Wipe the spigot opening with a dry towel and check closely for any lingering drips.
  8. Refill the tank completely: Turn the top cold water inlet valve back to full open. Keep your upstairs hot water sink faucet open. At first, the faucet will sputter and spit air. Once a solid, steady stream of cold water flows from the sink tap without air bursts, your water heater tank is full. Turn off the sink faucet.
  9. Turn the power or gas back on: Only after the tank is completely filled with water should you restore power. Flip the electric circuit breaker back on, or turn the gas valve knob back to your desired temperature setting.

The Risk of Flushing an Old or Neglected AO Smith Heater

Homeowners often discover their water heater has been running untouched for eight, ten, or twelve years. The natural reaction is to rush down with a garden hose and drain it immediately. In an old, neglected tank, this can actually destroy the unit.

Over a decade of neglect, mineral scale builds into a hardened crust several inches thick. Beneath that crust, corrosive water and rust pits may have eaten tiny pinholes into the steel tank wall. The hardened mineral layer acts like a makeshift plaster patch, holding the water inside and stopping those microscopic rust holes from leaking. When you perform a heavy flush on a severely neglected tank, you wash away that mineral seal. Within hours or days of the flush, water begins leaking through the exposed rust holes, ruining the tank beyond repair.

Older drain valves also present a serious mechanical risk. Many older water heaters use cheap plastic drain valves. If that plastic spigot has sat untouched in boiling water for ten years, the internal plastic stem becomes brittle. When you twist it with pliers, the stem can snap off in your hand, or the internal rubber washer can disintegrate. You end up with a wide-open valve that refuses to close, leaving you with an uncontrollable stream of hot water on your floor.

If your AO Smith heater is more than eight years old and has never been cleaned, do a gentle mini-flush instead of a full drain. Connect a hose, leave the cold water supply running under full pressure, and open the drain valve for just 30 seconds into a white bucket. If the valve opens easily, discharges water, and closes completely without dripping, you can flush it lightly. If the valve feels stuck, or if large chunks of dark rust flake out into your bucket, stop immediately. Close the valve and leave the tank alone. Start budgeting for a replacement water heater instead of risking a major flood.

How to Slow Down Mineral Buildup in Your AO Smith Heater

While an annual flush removes loose debris, taking active steps to reduce scale formation will make your flushes faster and extend the working life of your water heater.

The easiest adjustment is lowering your water heater thermostat. AO Smith recommends setting the dial to 120 degrees Fahrenheit. Many factory units leave the warehouse set at 130 or 140 degrees. Water temperatures above 125 degrees cause calcium and magnesium to separate from the water at an accelerated rate. By lowering the temperature dial to 120 degrees, you dramatically slow the speed at which scale bakes onto the tank walls, while still keeping your water hot enough for comfortable showers and sanitizing dishes.

For homes with severe mineral content, installing a whole-house water softener is the most reliable long-term solution. A water softener swaps hard mineral ions for sodium ions before the water ever touches your plumbing. This stops loose sand and mineral grit from ever settling on the bottom of the tank.

Keep a close eye on the anode rod (the metal rod inside that stops tank rust). This sacrificial magnesium or aluminum rod hangs inside the water to draw corrosive electrical currents away from the steel tank walls. When an anode rod wears down completely, corrosive minerals attack the bare tank metal directly. Check this rod every two to three years, and replace it when more than six inches of the thin interior core wire becomes visible.

The space where your water heater lives also impacts its workload. Units installed in drafty garages or open basements must work harder to retain heat against cold air. If your heater sits in a cold utility room, setting up a reliable electric heater for garage spaces during harsh winter months keeps the ambient air warm and stops icy inlet temperatures from overworking the burner. Similarly, for manufactured homes where the water heater is tucked into an exterior closet, pairing the space with an approved safe heater for mobile home utility areas helps prevent plumbing lines from freezing up during sudden cold snaps.

FAQs

Is flushing a water heater the same thing as draining it?

No, flushing and draining serve two different maintenance purposes. Draining means emptying all the water out of the tank to perform repairs, replace heating elements, or move the unit. Flushing means running water through the base of the tank to sweep loose mineral grit out through a hose, often by using quick bursts of fresh cold water pressure to clean the floor of the tank.

How long does it take to flush an AO Smith water heater?

A standard maintenance flush on a well-maintained heater takes between 20 and 30 minutes from start to finish. If your tank contains heavy sediment that clogs the bottom drain valve, clearing the blockage and waiting for the water to run clear can extend the process to about an hour.

Can I flush my water heater without turning off the gas or electric power?

Never flush or drain your water heater while the power or gas burner is running. If water drops below an active electric element, the element will burn out and melt within seconds. In a gas heater, firing the burner against an empty, dry steel bottom can crack the glass tank lining and permanently ruin the appliance.

What should I do if the drain valve will not stop dripping after a flush?

Drips usually happen because a piece of loose mineral grit got caught between the rubber washer and the valve seat. Thread your garden hose back on, turn the cold water supply on briefly, and open the drain valve for five seconds to blast the debris away before closing it tight. If it still drips, screw a brass 3/4-inch garden hose cap with a rubber washer onto the spigot threads to stop the leak completely until a plumber can replace the valve.

Related guides: how to flush ao smith tankless water heater.

4.3
3 ratings
John Clark
WRITTEN BY
John Clark
In the bustling city of Seattle, John Clark, a female editor, delves into the world of winter and outdoor products. His work, backed by 15 years of experience, is a treasure trove of practical tips and engaging stories.