Bestwinterproducts.com is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

How to Attach a Salomon Quiver to an Adv Skin 5 Securely

Prime for Young Adults: check your eligibility on Amazon

Most people assume a pole holder clips onto any handy loop, but that can leave it swinging or catching as you run. Use the holder’s matching loops or cords with the vest’s intended connection points, and don’t force a connection that doesn’t line up.

The right setup depends on which version of the vest you have, where its connection points sit, and whether the holder is meant to ride on your left or right side. Check the instructions for both pieces, then make sure the loaded holder clears your pockets and arm as you move. Here’s how to attach it and check the fit before setting off.

The Short Version

  • Check the instructions for your exact Adv Skin 5 and quiver before connecting anything. Their loops and cords may differ by version.
  • Match the quiver’s attachment loops or cords to the vest’s intended connection points. Don’t pull a cord through a loop just because it seems to fit.
  • Set the quiver on the side and in the direction shown in its instructions, then adjust the vest cords only as the instructions allow.
  • Before you run, load the poles and move your arms. The quiver should stay in place without swinging, catching, or covering a pocket.

Check the Vest and Quiver Before Attaching Them

Lay the vest and quiver out where you can see both clearly. Find the model and version information on each item, its label, or its instructions. The Adv Skin 5 may have different attachment points depending on its version, and the quiver’s loops or cords may also vary.

Look for the places the vest instructions identify for holding a quiver. Attachment points are the loops or other places where the parts connect. Don’t assume that every small loop on the vest is meant for the quiver; some may serve another purpose or may not be strong enough for a loaded holder.

Next, look over the quiver. Find the loops, cords, or other connections named in its instructions, and note which way the holder is meant to face. If the instructions show a particular side of the vest, follow that direction rather than choosing based on a photo of a different version.

Check whether the quiver is intended to sit on your left or right side. The correct side can depend on the quiver design and the vest version. A setup that looks neat when the vest is lying flat may still get in the way of your arm once you put the vest on.

Before connecting anything, make sure the cords and loops are not frayed, torn, or stretched out. If a connection looks damaged, don’t rely on it to hold poles while you run. Check the manufacturer’s instructions or contact Salomon for help identifying the correct connection points.

Match the Quiver Connections to the Vest

Use the vest’s named quiver attachment points and the matching connections on the quiver. The parts should meet naturally, without twisting a cord, stretching a loop hard, or forcing one piece through a place that does not line up. A connection that takes force or looks improvised is a reason to stop and check the instructions.

The routing is the path a cord follows between the quiver and vest. Follow the path shown for your two items, including which loop the cord passes through and where it fastens. A cord routed around the wrong part can leave the holder loose or pull at the vest in a way its attachment points were not meant to handle.

Keep the quiver’s opening and pole-removal direction in mind as you match the pieces. The holder needs to stay accessible while you reach for poles, and its opening should not point into the vest or your arm. If the instructions don’t make the direction clear, look for a diagram for your exact version rather than copying a setup from a different vest or quiver.

Don’t adjust every vest cord just to make the quiver fit. Some cords may adjust the vest’s pockets or overall fit instead of holding the quiver. Change only the cord or connection the instructions identify, and make small adjustments so you can see whether the quiver sits correctly without pulling the vest out of shape.

Attach and Adjust the Quiver

  1. Start with the vest empty. Put it on or lay it flat as the instructions recommend. Empty pockets make it easier to see the attachment points and notice whether a cord is twisted.
  2. Choose the instructed side. Confirm whether your quiver belongs on the left or right. If the instructions show a specific position, use that position rather than moving it to another side to make a mismatched connection work.
  3. Line up the matching parts. Bring the quiver’s loops or cords to the vest’s intended attachment points. Check that the pieces sit in the same direction as the instructions show and that no fabric or pocket edge is trapped between them.
  4. Follow the cord path exactly. If a cord needs to pass through a loop or fasten to a point, follow the path in the instructions. Keep the cord flat and untwisted. Don’t knot it, add a different fastening, or pull it through a nearby loop unless the manufacturer says to do so.
  5. Adjust only the named cord. If the instructions allow an adjustment, take up enough slack to keep the quiver close to the vest. Don’t cinch it so tightly that the vest puckers, the loop stretches, or the quiver is hard to reach.
  6. Put in the poles as directed. The weight and shape of the poles can change how the holder hangs. Keep the poles secured in the way the quiver instructions show, and make sure they are not pressing into a pocket or shifting the holder away from the vest.
  7. Put the vest on and move naturally. Reach forward, swing both arms, bend, and turn your upper body. If the quiver catches your arm or shifts as you move, take it off and review the routing and adjustment before setting out.

Don’t assume a snug-looking fit while the vest is flat will stay snug when worn. The vest fabric can move as you run, and loaded poles can make a loose connection more noticeable. The final check should be with the vest on and the poles in the quiver.

Check for Swinging, Snagging, and Blocked Pockets

  • Check for movement. With the poles loaded, gently move the quiver by hand. It should remain in its intended position instead of hanging away from the vest or shifting with each small movement.
  • Check while moving. Walk, swing your arms, and turn your body. Watch for the quiver bumping your arm, flapping against the vest, or pulling the connection point.
  • Check for snags. Look for a cord that sticks out, catches on a pocket edge, or crosses where your arm moves. Smooth the cord only in the way the instructions allow.
  • Check access to pockets. Open and close nearby pockets and reach for what you carry there. The holder should not cover a pocket opening or make it hard to get something out.
  • Check the poles. Make sure the poles stay seated when you move and that they can be removed in the intended direction. If a pole slides out or the quiver shifts, don’t start running until you’ve corrected the fit.

A quiver that swings can rub your side, catch your arm, or loosen as you move. If you notice any of those problems, stop and remove the vest before changing the setup. Don’t try to hold the quiver in place by tying extra knots or adding an unapproved strap.

Repeat the checks after changing what you carry in the vest. A full pocket can press against the quiver or change how the vest sits on your body. What feels clear with empty pockets may feel crowded once you add food, a phone, or other gear.

If the Attachment Points Don’t Line Up

Stop if the quiver’s connections don’t meet the vest’s intended attachment points. Don’t force a cord through a tight opening, stretch a loop beyond its normal reach, or attach the holder to a random vest loop. Forcing the parts can damage a cord or attachment point, and it may still leave the quiver loose.

Check the instructions for both items again, paying close attention to the version names and any pictures showing the quiver’s side and direction. Confirm that you have the correct instructions for the vest you own, not a similar-looking version. If either set of instructions is missing, ask Salomon or the quiver’s maker to confirm the correct connection for those specific items.

If the instructions show different connection points from the ones on your vest, don’t treat that as a problem you can solve by improvising. The vest and quiver may use different setups, or you may be looking at instructions for another version. Get confirmation from the manufacturer before carrying poles in that arrangement.

Don’t run with a holder that shifts, catches, or cannot be secured using its intended connections. If a loop is damaged or the instructions still leave the correct routing unclear, contact the manufacturer for guidance. That is safer than finding out on a trail that a pole has slipped free or the holder is pulling on the vest.

FAQs

Which Adv Skin 5 loops should I use?

Use only the attachment points identified for a quiver in the instructions for your exact vest version. A loop that looks convenient may not be intended to carry a loaded holder. If the named points are unclear, ask Salomon to identify them before attaching the quiver.

How should the quiver face?

Follow the direction shown in the quiver instructions, including whether it sits on the left or right. The opening should remain accessible, and the loaded holder should not block a pocket or meet your moving arm. If your version’s instructions don’t show its direction, confirm it with the manufacturer rather than guessing.

Do I need to adjust the vest cords first?

Only adjust a cord if the instructions say that cord is used to attach or position the quiver. Other cords may affect the vest or its pockets. Make a small adjustment, then check the fit with the vest on and poles loaded.

What if the quiver fits but still swings?

Take the vest off and check that the cord follows the correct path and that the connection is fully seated. Confirm that the quiver is on its instructed side and that the poles are held as directed. If it still moves or the attachment points don’t match, don’t run with it; contact the manufacturer for help with your exact versions.

Related guides: how to attach salomon quiver to adv skin 5.

4.5
2 ratings
Sheldon Morrison
WRITTEN BY
Sheldon Morrison
My name is Scott Sample, a editor from Los Angeles. For the past 20 years, I have specialized in luxury winter and outdoor products, providing expert advice and insights to readers nationwide.