How to Change Ski Pole Grips Without Forcing Them
A worn or loose ski pole grip usually isn’t a reason to worry, but it should be secure before you head out. Most grips come off by loosening the glue or other hold between the grip and the pole’s long tube, then fitting a replacement the way its maker directs. Don’t force a stuck grip, since that can damage the pole or leave the new grip loose.
The right steps depend on how the grip is attached, what the pole tube is made of and how it’s shaped, and whether the replacement fits that pole. Some grips may use screws or another hold instead of glue, so heat or tools that work for one design could harm another. Start by checking the grip and pole, then gather what you need for the correct removal method.
How can you tell how the grip attaches?
Look closely at the top and bottom of the grip before you try to remove it. The grip is the part you hold, and the shaft is the long pole tube beneath it. Some grips are glued onto the shaft, some use a screw or another fastening part, and some have a design that needs a particular removal method.
Check the pole maker’s instructions first, if you have them. Also look for a small screw or cap near the top of the grip, and inspect the area where the grip meets the shaft. A visible fastener may mean the grip is not simply glued in place. Don’t pry at a cap or pull hard to find out.
Compare the old grip with the replacement before doing any work. The replacement must suit the shaft’s shape and size, and it must attach in a way that matches the pole’s design. A grip that looks close but does not fit properly can slip, twist, or come off while you ski.
Replacing a grip is not always practical at home. If you cannot identify how it is held, or the pole maker says the grip is not meant to be replaced, ask a ski shop before you start. A shop can also help confirm that a replacement is right for the pole.
What should you gather first?
Follow the instructions for both the pole and the new grip. The grip maker may specify a certain tool, attachment method, or product to use. Do not assume the method that worked for another pole will work for yours.
- The pole instructions: Find the maker’s directions for removing the old grip and attaching a new one. If you do not have them, check with the pole maker or a ski shop.
- A compatible replacement: Confirm that the new grip fits your shaft and uses the right attachment method. Check the maker’s fit information rather than relying on appearance alone.
- Only the tools the instructions call for: Set them out before you begin. If the directions require a tool you do not have, pause and ask a ski shop instead of substituting a knife, pliers, or another tool.
- A clear, steady work area: Keep the pole still and away from other gear while you work. A clean surface makes it easier to see the joint and keep loose parts from getting lost.
- The strap, if you plan to reuse it: Check whether the old strap is attached to the grip or the pole, and whether the maker’s directions allow it to be moved to the new grip.
Work with a dry pole so you can see the joint and keep your hands from slipping. Set the pole down if you cannot hold it steady. Avoid starting the job just before leaving for the mountain, when it may be tempting to rush a grip that is not going on easily.
How do you remove the old grip?
Use the removal method for your pole’s design. The steps below are a careful order of checks, not a universal way to pull off every grip. Stop if the maker’s directions differ, if the grip will not move as described, or if the shaft begins to bend or show damage.
- Secure the pole. Place it where it cannot roll or slide. Hold the shaft steady without crushing it or clamping it in a way that could bend or mark it.
- Remove a fastener only if the instructions say to. If the grip has a screw or another visible fastening part, use the stated tool and method. Keep small parts together. Do not twist a screw, cap, or plug that the instructions do not identify as removable.
- Release the strap as directed. Some straps pass through or attach to the grip. Check how yours is connected before pulling. If the strap catches, stop and look for a fastener or opening rather than yanking it.
- Loosen the grip only in the approved way. For a grip held by glue, the maker may give a method for loosening that bond, which means the glue or hold between the grip and shaft. Follow those directions exactly. Do not use heat or a solvent unless the pole or grip maker specifically says to, because the shaft or grip could be damaged.
- Ease the grip away as directed. Keep the pole straight and use controlled pressure. Do not lever a tool against the shaft or wrench the grip from side to side. If it stays stuck, stop rather than increasing force.
- Inspect the exposed shaft. Look for cracks, deep scrapes, bends, crushed spots, or material that has come loose. If you see damage, do not fit a new grip and ski with it. Ask a ski shop whether the pole can be repaired or should be replaced.
A grip that does not move is a reason to pause, not a sign that you need to pull harder. The grip may be held by a screw, a different bond, or a feature you cannot see from the outside. Forcing it can damage the shaft, and damage under the grip can make the new attachment unreliable.
Keep sharp tools away from the shaft and your hands. If the instructions call for a blade or another sharp tool and you are unsure how to use it safely, leave that part to a ski shop. Never cut toward yourself or use a tool as a lever against the pole.
How do you fit the replacement grip?
Match the new grip to the pole before attaching anything. Set the parts beside each other and check their shape, openings, and strap connection against the maker’s instructions. If the grip does not line up or appears to need force to start, do not press it into place.
- Clean the shaft only as directed. Remove loose dirt or old material only by the method the pole or grip maker permits. Do not scrape, sand, or apply cleaner unless the instructions allow it.
- Set up the attachment method. If the grip uses a screw, glue, or another fastening method, follow its maker’s directions for that method. Use only the materials and steps specified. Do not add glue to a grip that is designed to attach another way.
- Align the grip carefully. Make sure the grip points the right way and the strap opening lines up with the pole. Start the grip as the directions describe, keeping the shaft straight. If it catches, stop and check alignment instead of pushing harder.
- Attach it fully as directed. Follow the stated order for tightening or securing the grip. Do not guess how tight a fastener should be, and do not use extra force to make the grip sit flush.
- Leave it undisturbed for the stated time, if any. If the maker gives a waiting period before use, follow it. If the instructions do not explain when the pole is ready, ask the grip maker or a ski shop rather than guessing.
After fitting the grip, check that it sits straight and does not shift when you hold it normally. A small gap, visible misalignment, or movement may mean the grip has not attached correctly. Do not ski with a grip that feels loose, even if it looks seated from the outside.
Do not use a hair dryer, hot water, or another heat source to make a grip easier to fit unless the maker specifically approves that method. Heat can affect the pole or grip. A method used for one material or design may not be suitable for another.
Can you reuse the old strap?
Sometimes, but only if the strap is in good condition and the maker’s directions allow it. Check the whole strap for cuts, fraying, worn stitching, stiff or damaged sections, and a worn attachment point. A strap that may break or slip is not worth keeping just because the grip has been replaced.
Look at how the strap connects to the old grip before removing it. The new grip must accept the strap in the same intended way, or have a different strap arrangement specified by its maker. Do not cut, knot, or force the strap into an opening that does not match.
If the strap is damaged, does not fit the new grip, or cannot be attached securely, ask the pole maker or a ski shop about a suitable replacement. Make sure the strap sits correctly around your hand and does not bind when you hold the pole. If the attachment is uncertain, leave the pole unused until it is fixed.
How do you check the grip before skiing?
Check the pole at home, before you head out. Hold the shaft in one hand and the grip in the other. Gently try to turn and move the grip in the ways it might shift during normal use. It should not twist, slide, or pull away from the shaft.
- Look around the joint for a gap, a tilted grip, or a fastener that is missing or loose.
- Hold the grip as you normally would and make sure the strap stays attached and sits comfortably around your hand.
- Check that the shaft still looks straight and has no new cracks, splits, bends, or crushed areas.
- Confirm that any glue or other attachment has had the time the maker requires before you use the pole.
These checks can reveal a grip that is not seated or attached properly, but they cannot make a damaged shaft safe. If anything moves unexpectedly, or you cannot tell whether the attachment is sound, do not ski with that pole. Have a ski shop look at it.
When should you ask a ski shop?
Ask a ski shop if the grip is stuck, the attachment is unclear, or the maker’s directions are missing or confusing. A shop is also the safer choice if the pole has a screw or strap fitting you cannot release without force, or if the replacement does not match the shaft.
Stop immediately if the shaft bends, cracks, splinters, or gets deeply scratched while you work. Also stop if the grip breaks apart or a fastening part will not come out as directed. More force can turn a difficult removal into a damaged pole.
Get help if the new grip will not sit straight, will not stay in place, or leaves the strap insecure. A ski shop can check whether the pole and replacement are compatible and whether the pole is still usable. Until the grip and pole are secure, use another pole that is in sound condition.
FAQs
Can you change a ski pole grip at home?
Often, if the grip is meant to be replaced and you can follow clear instructions for that pole and grip. The attachment method and shaft design matter. If you cannot identify them, ask a ski shop before removing anything.
Can you use heat to remove a glued grip?
Only use heat if the pole or grip maker specifically allows it and explains how. Heat can damage some pole or grip materials. Do not choose a heat method just because the grip seems stuck.
What if the new grip feels loose?
Do not ski with it. Check the maker’s directions for the correct fit and attachment, but do not add glue or tighten parts by guesswork. If the grip still moves, take the pole and replacement to a ski shop.
Do replacement grips fit every ski pole?
No. The replacement must suit the pole’s shaft shape, size, and attachment design. Confirm compatibility with the grip maker or a ski shop before you begin.
Related guides: how to remove ski pole grips and how to remove leki ski pole grips.





















